ISO 2768 for CNC RFQ — Prototype China

ISO 2768 vs tight tolerance for aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China? Put ISO 2768-m (or f) once — on a 100 mm size class m allows ±0.3 mm, not ±0.1 — then box the fits that earn money. Open aluminum enclosure China, CNC prototype China, small-batch CNC China or humanoid robot enclosure China, then Upload STEP on /contact/ — usually one working day.

Upload STEP & start China factory RFQ

A buyer sends a drawing and gets a China CNC quote back at nearly double what they budgeted. They ask why, and the answer is usually in the title block, in six characters nobody reads closely: ISO 2768-m.

The general tolerance callout is the most common cause of a quote that lands higher than expected. The cause is rarely padding. A drawing can ask for something the geometry cannot deliver cheaply, and nobody notices at the point the tolerance is set. Route landings after class vs boxed fits: aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China. Pair this page with the RFQ tolerance guide, the CNC tolerance chart, the drawing package checklist, DFM first article, and the machine route on CNC machining China · all services · quality system. Upload STEP: /contact/.

Upload STEP & request prototype China CNC RFQ

What the callout actually says

ISO 2768-1 sets default tolerances for linear and angular dimensions that carry no individual tolerance. It has four classes: f (fine), m (medium), c (coarse) and v (very coarse). Most drawings use m, because it is the default in most CAD templates.

Here is what m means in practice. On a linear dimension of 100 mm, class m allows ±0.3 mm. Class f allows ±0.15 mm.

That figure is often read as ±0.1 mm, which is three times tighter than the callout asks for. The gap matters in both directions. A part held to m is cheaper than its drawing suggests, and a part where someone wrote ±0.05 on a mating face has quietly moved two classes tighter than the title block says.

Where the money goes on a China CNC RFQ

Cutting passes

A feature at ±0.3 mm can be cut in one pass at full depth. At ±0.05 mm the same feature needs a roughing pass that leaves stock, then a finishing pass that removes it at a lighter depth and a slower feed. Machine time rises before anything else changes.

Set-ups and datums

Tight features usually have to be machined in the same set-up as their datum, otherwise the tolerance stack between set-ups eats the band. That often means a fixture that would not otherwise exist, and a fixture is a one-off cost that lands on the first order.

Inspection

The wider the band, the cheaper the check. A general-tolerance feature can be verified with hand gauges; at ±0.02 mm it moves to a CMM. On prototypes and machined parts, inspection here runs 100% on a Zeiss CMM and a ROMER measuring arm, and the report ships with the parts. Batch production drops to 5% random sampling at an agreed depth, inside the prototype workflow. See also how Everoyal inspects.

Scrap

The narrower the band, the higher the share of parts that fall outside it. A process running at ±0.05 mm capability against a ±0.02 mm requirement will reject a share of what it makes. That rejection is priced into the unit cost whether it happens or not.

What each class changes on the shop floor

For an aluminium enclosure in the 100 mm range, machined from billet in China, the callout decides the route before the quote exists.

ToleranceDeviation at 100 mmWhat changes on the shop floor
ISO 2768-m±0.3 mmOne pass at full depth; checked with hand gauges
ISO 2768-f±0.15 mmFinish pass in the same set-up
Boxed ±0.05 mm±0.05 mmRough and finish split; datum cut in the same set-up
Boxed ±0.02 mm±0.02 mmHigh-speed or five-axis finishing; CMM measurement
Boxed ±0.01 mm±0.01 mmPrecision bore work; CMM report with the parts

The step that changes the process rather than the number is the one from general tolerance to ±0.02 mm. A ±0.3 mm feature can be cut once and checked with a caliper. A ±0.02 mm feature needs a roughing pass, a finishing pass and a measurement that proves the result.

These changes scale with geometry. A thin wall distorts and costs more to hold than a solid boss. A deep pocket needs longer tools and lighter cuts. A part that has to hold tolerance after anodising is a different problem, because anodising moves surfaces by a few microns and the tolerance has to survive that.

What that adds to a price depends on the part and the quantity. It is quoted per programme, not read off a multiplier. Band tables: CNC machining tolerance chart. How to write fits into the RFQ: RFQ tolerance guide.

Blanket tolerance is the expensive habit

Some features genuinely need ±0.02 mm. A bearing bore, a joint interface, a dowel location. Nobody should loosen those.

The mistake is blanket tolerance. A drawing where every dimension carries ±0.02 mm, because that felt safer than deciding which ones matter, is priced as a ±0.02 mm part across the board. If three dimensions drive function, the other thirty-seven buy insurance nobody asked for.

Cost is set by the tightest feature on the part. That is the single most useful thing to understand about a prototype quote.

How to mark a drawing so the China RFQ matches

Keep the general tolerance in the title block. It is a sensible default and it saves everyone time. Then do four things. Full packing list: what to include in a drawing package.

Box the dimensions that matter

Six or fewer on a typical enclosure. A boxed dimension tells the supplier this one is functional, and everything unboxed can sit at the general tolerance.

Say what the feature does

"Mates with housing, bore Ø12 H7" is more useful than a bare tolerance, because it tells the supplier which failure mode to avoid. Work gets routed differently when a bore is known to be a bearing seat rather than a clearance hole.

Tolerance the datum, not just the feature

A ±0.02 mm bore measured from a datum that is itself only located to ±0.3 mm is not a ±0.02 mm bore in the assembly. A good share of tolerance arguments in prototype programmes start here.

State the inspection you expect

If the part needs a full CMM report, say so on the drawing rather than after the first shipment. It changes the price and the schedule, and finding out late costs both sides.

What to ask a supplier before the quote

Three questions separate a supplier who reads drawings from one who prices them.

Which features are driving this price?

If the answer names the same two or three dimensions you were worried about, they looked at the geometry. If the answer is a single number, they did not.

What would this cost at 2768-f?

The answer tells you what your tolerance choice is buying, in money, before you commit to it.

Where is the risk in this drawing?

A supplier who cannot name a risk has not reviewed the part, whatever the cover email says.

A quote is a reading of the drawing. If the drawing says ±0.02 mm forty times, the quote will say so too, in a currency you did not choose. Twenty minutes spent deciding which six dimensions matter is usually worth more than shopping the same drawing to a fifth supplier.

Which route a part should take in the first place is covered in which process a robot enclosure should use. Machine RFQ path: CNC machining China.

Questions

ISO 2768 vs tight tolerance FAQ

ISO 2768 vs tight tolerance for aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China?

Put ISO 2768-m (or f) once in the title block — on a 100 mm size class m allows ±0.3 mm, not ±0.1 — then box only the fits that earn money. Open aluminum enclosure China, CNC prototype China, small-batch CNC China or humanoid robot enclosure China for the matching route, then Upload STEP on /contact/ (up to 2 files × 4 MB; usually one working day).

Is ISO 2768 still current?

ISO 2768-1 remains the reference most drawings still use for general tolerances. Check the revision noted in your own title block and keep it consistent across a programme, because a supplier prices against whatever the drawing states.

What does ISO 2768-m mean for a 100 mm dimension?

It allows ±0.3 mm. Class f allows ±0.15 mm on the same dimension. The figure is often read as ±0.1 mm, which is tighter than either class asks for.

How much does tightening a tolerance cost on a China CNC RFQ?

Tightening a tolerance changes the route more than the number. A ±0.3 mm feature runs in one pass; a ±0.02 mm feature needs a roughing pass, a finishing pass and a CMM measurement. What that adds depends on the geometry, the material and the quantity, so it is quoted per programme.

Should every dimension be toleranced individually?

No. Keep the general tolerance in the title block and box the six or fewer dimensions that carry function. Cost is set by the tightest feature, so tolerancing everything tightly prices the whole part as a precision part.

Which landing should I open for an aluminum enclosure China RFQ after this ISO 2768 cost page?

Open /services/aluminum-enclosure-china/ for enclosure-specific route language. Use this page for class vs boxed-fit cost, then upload STEP on /contact/.

When should I choose CNC prototype China after reading ISO 2768 vs tight tolerance?

Open CNC prototype China when you are ready to cut metal. Bring ISO 2768 class and only the boxed fits from this page so the prototype quote is comparable.

How does small-batch CNC China use the same ISO 2768 cost logic?

Open small-batch CNC China when repeatable metal parts follow the same title-block class and boxed fits. Cost is still set by the tightest feature, not by blanket ±0.02 mm.

Can humanoid robot enclosure China programs reuse this ISO 2768 vs tight tolerance guide?

Yes. Open humanoid robot enclosure China for shell RFQ language, then use this page to keep ISO 2768-m once and box only joints, bearings and sealing faces.

Which service page should I open before a China manufacturer RFQ after reading this ISO 2768 cost page?

Pick the matching dedicated landing: aluminum enclosure China, CNC prototype China, small-batch CNC China, or humanoid robot enclosure China, then upload STEP on /contact/ (up to 2 files × 4 MB; usually one working day).

Does anodising affect tolerance?

Yes. Anodising moves surfaces by a few microns, and the coating builds on the surface rather than into it. If a feature has to hold tolerance after finishing, say so on the drawing, because the pre-finish dimension has to be adjusted for it. Sister landing: anodizing China.

Where do I upload a prototype China CNC RFQ with ISO 2768 callouts?

On the contact form — up to 2 files, 4 MB each (STEP, IGES or PDF). Name the general class and box fit-critical sizes. An engineer replies with route, DFM risks and quotation, usually within one working day. WhatsApp +86 138 2330 4476 and sales@everoyalprecision.com also work.

Related helpers

Four new landings, ISO 2768 helpers & RFQ → /contact

Aluminum enclosure China

Billet CNC shells — keep class m and box only enclosure fits.

CNC prototype China

Cut metal with ISO 2768 class and boxed fits from this page.

Small-batch CNC China

Same class vs tight-fit logic for repeatable metal bands.

Humanoid robot enclosure China

Shell RFQ; box joints and bearings, leave the rest at general.

CNC tolerance chart

ISO 2768 bands and feature limits beside this cost page.

RFQ tolerance guide

How to write class and fits into the same RFQ pack.

Drawing package

STEP + PDF checklist that carries the title-block class.

Contact / RFQ

Upload STEP (up to 2 files, 4 MB each) for a China factory quote.

Upload STEP & start China factory RFQ

China factory RFQ

Upload STEP — ISO 2768 vs tight fits → /contact

Attach STEP, IGES or PDF on /contact/ (up to 2 files, 4 MB each). Name the general class and box the fits that earn money. Rocky Chen replies with a process route, DFM risks and a quotation — usually within one working day. Route landings: aluminum enclosure, CNC prototype, small-batch CNC, humanoid robot enclosure.

Upload STEP & start China factory RFQ

ContactRocky Chen
BaseSuzhou, Jiangsu, China. Visits by appointment.