17-4PH, 303 & 304 Stainless — CNC Grade Picks
Updated 2026-11-17 · Semrush cluster P26 · 17-4PH H900 · prior P9 303s · P2 P stainless grades (17-4 / 303 / 304) · Google P4 G2 passivation · P5 medical hardlink.
Stainless vs aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China? Stay here for 303/304/316/410 when corrosion or weldability drives the grade. Choose aluminum enclosure China or humanoid robot enclosure China when weight, anodize or EMI favor aluminum shells; open CNC prototype China or small-batch CNC China when the metal route is decided — then Upload STEP on /contact/ (usually within one working day).
Stainless vs aluminum for enclosures and CNC parts? Stainless is chosen for corrosion resistance and then fought on the shop floor: it work-hardens, holds heat and wears tooling faster than aluminum. Specifying 304 for a turned part that could be 303 can roughly double cycle time with no functional gain unless the part is welded. Route landings: aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China. Side-by-side: aluminum vs stainless China CNC. Then Upload STEP on /contact/.
17-4PH, 303, 304 and 410: the practical CNC differences
| Grade | Use it for | Machining behaviour |
|---|---|---|
| 17-4 / 17-4PH | Fixtures, shafts, parts that need strength after aging | Name 17-4PH H900 or H1150 — not only “17-4”. Easier in Condition A, then age; or machine already in the called condition |
| 303 / 303s | Turned and milled parts, fittings (free-machining) | 303s stainless steel — sulphur free-machining; easiest chips; avoid if welded |
| 304 | General corrosion resistance, welded structures | Work-hardens quickly; light cuts and constant feed matter |
| 316 | Chemical and marine service | Harder than 304, better corrosion, slower to cut |
| 410 | Wear pairs, valve parts, hardenable parts | Machinable to a wear surface, then heat treated |
| 430 | Sheet parts, appliance panels | Formable, magnetic, less corrosion resistance than 304 |
The distinction that decides cost: 303 is a free-machining grade with sulphur added specifically to break chips. Specifying 304 for a turned part because it is the grade everyone knows can double the cycle time for no functional gain, unless the part is welded or needs 304's corrosion resistance.
303s stainless steel — free-machining 303 vs 304 / 316 for CNC
303s stainless steel (often written 303 / 303S) is the free-machining austenitic pick: sulphur breaks chips so turned fittings and milled brackets finish faster than 304 or 316. Prefer 304 when the part is welded or needs general corrosion in a welded assembly; prefer 316 for chemical / marine service. 303 is a poor weld choice — sulphur hurts weld integrity. We do not publish catalogue prices or invent ISO/FDA claims. Upload STEP → /contact/.
| Question | Lean 303 / 303s | Lean 304 / 316 |
|---|---|---|
| Turned fittings, no weld | Usually 303s — cycle time wins | 304 only if corrosion/weld narrative requires it |
| Welded assembly | Avoid 303 | 304 general; 316 chem/marine |
| Passivation after CNC | Call it when corrosion matters | Same — not a substitute for grade |
| RFQ must name | 303 or 303s, qty, need-by | 304 vs 316 + weld yes/no |
Upload STEP — 303s / stainless RFQ CNC machining China
17-4PH H900 (and H1150) — call the condition, not only the grade
17-4PH H900 is a heat-treat condition, not a second alloy. On a China CNC RFQ, name 17-4PH H900 or 17-4PH H1150 — or Condition A if the part will be aged after machining. A print that only says “17-4” leaves stock state, hardness and whether a later age is allowed open, and two quotes will assume two different things. This section is about 17-4 PH stainless steel machining and 17-4 stainless steel machinability as they change with the called condition. Upload STEP → /contact/.
17-4PH H900 is the peak-strength aging condition; 17-4PH H1150 is overaged and softer, usually picked when toughness or dimensional stability after aging matters more than peak strength. 17-4 stainless steel machinability is better in Condition A; aging afterward can move a tight bore, so say whether critical fits are held after heat treat. Machining already-aged 17-4PH H900 avoids that second movement and is harder on the cutter. No catalogue prices, no invented ISO/FDA claims. Sister route: CNC machining China. Upload STEP → /contact/.
| Condition to name | What it means on the RFQ | Machining implication |
|---|---|---|
| Condition A (solution annealed) | Softest starting stock; aging still to be done after the cut | Better 17-4 stainless steel machinability; size can move when later aged to H900 or H1150 |
| 17-4PH H900 | Peak-strength aging condition — write it, not only “17-4” | Harder on tools if you machine it already aged; no second heat-treat move if you finish in this condition |
| 17-4PH H1150 | Overaged, softer than H900 | Usually more dimensional stability after aging; still name it — “17-4” alone is not H1150 |
| Who ages the part | Arrives already in H900/H1150, or arrives in Condition A and is aged after machining | Say who does the age. This page does not invent an in-house heat-treat certificate. |
Upload STEP — 17-4PH H900 RFQ CNC machining China Aluminum vs stainless
Why stainless fights the cutter
- It work-hardens. A cut that rubs instead of shearing hardens the surface, and the next pass cuts hardened material. Constant feed and no dwell is the rule; a cautious slow pass is the one that ruins the part.
- It holds heat in the cut. Low thermal conductivity means the edge runs hot, which is why tool life drops faster than in aluminum or mild steel and why coolant delivery matters more than coolant volume.
- It galls and welds to the tool. Stainless will pick up on an edge and tear the surface. Sharp, correctly coated tooling and a generous chip load prevent it.
Laser cutting or machining
| Route | Right for | Limits |
|---|---|---|
| Laser cutting | Flat parts, brackets and panels under about 6 mm, no tooling cost | Through-thickness edge quality varies; no 3D features |
| CNC machining | 3D features, bores, threads, tight tolerance | Slower per part, more material wasted |
| Laser plus forming | Flat brackets and frames: cut flat, then bend | Bend relief and hole-to-bend distance still apply |
For a flat stainless bracket, laser cutting followed by forming is almost always cheaper than machining it from solid, because there is no tooling and no stock removal. The decision changes once the part needs a bore with a tolerance or a pocket: that is a machining operation, and the part is usually designed as laser-cut blank plus machined features.
Corrosion is a design decision, not only a material one
Stainless resists corrosion because of a passive chromium oxide layer. That layer needs oxygen, and it cannot reform in a crevice where stagnant water sits. So a 304 part with a tight crevice joint can corrode faster than a 316 part with the same joint drained properly.
- Avoid closed crevices and blind tapped holes that trap water; specify drainage where relevant.
- Do not mix carbon steel fasteners into a stainless assembly; the fastener corrodes and takes the stainless with it.
- Pickled or passivated finishes restore the oxide layer after welding, which welding locally destroys.
Specifying a stainless part on the drawing
- Say whether it is welded. That single fact decides between 303 and 304 more often than any other consideration, and it changes the price materially.
- Name the passivation requirement. Welded assemblies need pickling or passivation to restore the oxide layer, and it is a separate operation.
- State the service environment. "Wet, chemical or marine" moves the choice to 316; a dry indoor bracket does not need it.
- Show drainage where water can sit. A blind tapped hole or a closed crevice will corrode regardless of grade, because the passive layer cannot reform without oxygen.
One practical note on laser-cut stainless: the cut edge has a different surface from the rolled face and passivates differently. Where appearance matters, either the edge is finished or the drawing says the cut edge is acceptable as-is.
Related routes
Aluminum enclosure China
Aluminum shell when weight, anodize or EMI beats stainless corrosion needs.
CNC prototype China
First-article metal — stainless or aluminum — with grade named in the RFQ.
Small-batch CNC China
Repeatable lots; 303 vs 304 still decides cycle time on turned parts.
Humanoid robot enclosure China
Shell RFQ; mix stainless brackets with aluminum structure in one RFQ.
Aluminum vs stainless China CNC
Side-by-side when the metal choice is still open.
Contact / STEP upload
Rocky Chen — process route, risks and quote, usually within one working day.
Stainless vs aluminum / CNC FAQ
Stainless vs aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China?
Stay here for 303/304/316/410 when corrosion or weldability drives the grade. Choose aluminum enclosure China or humanoid robot enclosure China when weight, anodize or EMI favor aluminum shells; open CNC prototype China or small-batch CNC China when the metal route is decided. Then Upload STEP on /contact/ — usually within one working day.
When should I choose stainless instead of aluminum for an enclosure?
Choose stainless when corrosion, chemical/marine service or a welded assembly needs 304/316. Choose aluminum when weight, anodize cosmetics or EMI matter more — stainless work-hardens, holds heat and wears tooling faster than aluminum, so cycle time and cost rise unless the function needs it.
Is 304 or 303 better for machined stainless parts?
303 for turned and milled parts that are not welded: the added sulphur makes it free-machining and roughly halves cycle time. Use 304 where the part is welded or needs its corrosion resistance in a welded assembly.
Why does stainless steel work-harden during machining?
A cut that rubs rather than shears hardens the surface layer, and the next pass cuts hardened material. Constant feed with no dwell prevents it; a slow cautious pass causes it.
Can stainless steel parts be laser cut?
Yes, up to roughly 6 mm for flat brackets and panels, with no tooling cost. Parts that need bores, threads or pockets are designed as a laser-cut blank with machined features.
Do stainless parts need passivation after welding?
Yes. Welding destroys the passive oxide layer locally, so pickling or passivation restores it. Without it the weld and its heat-affected zone corrode first.
Which landing for an aluminum enclosure China RFQ after this stainless page?
Open /services/aluminum-enclosure-china/ when the shell should be aluminum. Use this stainless page for 303/304/316 grade and passivation language, then upload STEP on /contact/.
When should I choose CNC prototype China for a stainless first article?
Open CNC prototype China when you are ready to cut metal — stainless or aluminum. Bring grade (303 vs 304), weld yes/no and passivation need so the usual one-working-day reply can carry a firm route.
Do CNC stainless parts need passivation after machining?
Usually yes when corrosion resistance matters — machining can leave free iron. Call passivation on the RFQ for 303/304/316. Not a substitute for grade choice. Surface compare → /insights/cnc-surface-finish-ra-rfq/. Upload STEP → /contact/.
How does small-batch CNC China use the same stainless grade logic?
Open small-batch CNC China for repeatable metal lots. Specifying 304 for a turned part that could be 303 can roughly double cycle time with no functional gain unless the part is welded.
Can humanoid robot enclosure China programs use stainless brackets with aluminum shells?
Yes. Open humanoid robot enclosure China for shell RFQ language. Use this page for stainless fittings/brackets (303/304) that sit with aluminum structure; name both grades in the same RFQ on /contact/.
When is laser cutting cheaper than machining stainless from solid?
For a flat stainless bracket under about 6 mm, laser cutting followed by forming is almost always cheaper than machining from solid — no tooling and no stock removal. Once the part needs a bore with a tolerance or a pocket, design a laser-cut blank plus machined features.
Where do I upload drawings for a stainless or aluminum China RFQ?
On /contact/ — Rocky Chen replies with a process route, tolerance risks and a quotation, usually within one working day. WhatsApp +86 138 2330 4476 and sales@everoyalprecision.com also work.
When should I specify 17-4PH stainless steel instead of 303 or 304?
Use 17-4 / 17-4PH when strength after heat treat matters (fixtures, shafts). Use 303 stainless for free-machining turned parts; 304 when weld/general corrosion wins. Call condition on the RFQ. Upload STEP → /contact/.
What is the practical difference in 304 vs 303 stainless steel for CNC?
303 cuts faster (sulphur free-machining); 304 welds and corrodes better in general service. Specifying 304 for a turned fitting “because everyone knows it” often raises cycle time with no functional gain. RFQ → /contact/.
Do you machine 17-4 stainless and 303 stainless turned parts in China?
Yes — stainless steel machining for 17-4PH, 303, 304, 316, and 410 on the Suzhou CNC path. Sister China factory page → /services/cnc-machining-china/. RFQ → /contact/.
What is 303s stainless steel and when should I specify it for CNC?
303s stainless steel (303 / 303S) is free-machining austenitic stainless — sulphur improves chip break so turned and milled parts finish faster than 304 or 316. Use it for non-welded fittings and brackets. Prefer 304 when welded; 316 for chemical/marine. See 303s vs 304/316. Upload STEP → /contact/.
Should I choose 303s stainless steel or 304/316 for a CNC turned part?
Choose 303s when there is no weld and cycle time matters. Choose 304 for welded or general corrosion assemblies; 316 for chemical/marine. Specifying 304 for a simple turned fitting often raises cycle time with no functional gain. Upload STEP → /contact/.
What is the difference between 17-4PH H900 and H1150 on a CNC RFQ?
17-4PH H900 is the peak-strength aging condition; 17-4PH H1150 is overaged and softer, usually chosen when toughness or stability after aging matters more than peak strength. Name the condition on the print — “17-4” alone is not enough. See 17-4PH H900. Upload STEP → /contact/.
Should I machine 17-4PH in Condition A and then age it, or machine it already in H900?
Both are valid 17-4 PH stainless steel machining routes. Condition A cuts more easily, then the part is aged to H900 or H1150 — say whether tight fits are held after that age, because size can move. Machining already-aged 17-4PH H900 avoids the second movement and is harder on the cutter. Say which route the print requires. Upload STEP → /contact/.
Also useful: medical CNC China, aluminum vs stainless China CNC, aluminum grades, aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China, contact.
Stainless or aluminum — Upload STEP on /contact/
Attach drawings on /contact/. Rocky Chen replies with a process route, the tolerance risks in your data and a quotation — usually within one working day. Route landings: aluminum enclosure, CNC prototype, small-batch CNC, humanoid robot enclosure.