>

ABS vs PC vs Aluminum vs Titanium for Prototypes

Updated 2026-11-08 · Semrush cluster P7 · carbon fiber CNC / CFRP · prior P2 N aluminum vs titanium · Google gap P5 compare.

Which prototype materials for aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China? ABS for cheap painted covers; PC/PC-ABS for impact and heat; aluminum 6061/7075 for stiffness, threads and anodize. Open aluminum enclosure China or humanoid robot enclosure China for shells; CNC prototype China or small-batch CNC China when cutting metal is the decision — then Upload STEP on /contact/ (2 files × 4 MB; usually within one working day).

Why material choice drives the RFQ

Which prototype materials for aluminum enclosure / CNC prototype / small-batch / humanoid robot enclosure China? Overseas buyers often ask for "plastic or aluminum prototype from China" without naming the failure mode. ABS paints well and is cheap; PC survives impact and heat better; aluminum carries load, takes threads and anodizes. Route landings: aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China. The process follows the material — not the other way around.

Everoyal runs CNC, vacuum casting, 3D printing and rapid tooling at one Suzhou base, so a robot or automation program can mix ABS-like covers with 6061 frames under one quote. Deep grade tables: plastics and aluminum. This page is the decision + RFQ landing.

ABS / ABS-like

Cosmetic shells, painted covers, low-load brackets. Cheap to CNC or vacuum-cast; soft threads strip if you ask too much of them.

PC / PC-ABS

Impact and heat above ABS; still paintable as PC-ABS. Notch-sensitive — sharp internal corners crack under load.

Aluminum (6061 / 7075)

Stiffness, heat paths, precision bores, anodized cosmetics. Grade pick: 7075 T6 vs 6061 T6. Default metal for frames and housings on CNC China.

Upload STEP & request a materials quote

Side-by-side

ABS vs PC vs aluminum — what changes on the RFQ

FactorABS / ABS-likePC / PC-ABSAluminum 6061 / 7075
Best forPainted covers, mock-upsImpact / warmer environmentsStructure, heat, precision fits
Typical China routesCNC plate, vacuum cast, SLA/MJF, rapid toolCNC, vacuum cast (PC-like), print, rapid toolCNC first; print metal when earned
Tolerance realitySoft; warps after heavy cutBetter than ABS; watch notches0.01 mm bores / 0.02 mm position where earned
FinishPaint, texture, vapour polishPaint; limited plating gradesAnodize, blast, brush, polish
Common RFQ miss"Plastic" with no grade or paint noteSharp radii on impact partsAnodize without mask map
When to switchNeed stiffness or heat sink → AlNeed cheap paint shell → ABSNeed 50–500 cosmetic covers → cast / tool

Robot shell context: robot shell materials guide. Process pick helper: choose a process for a robot enclosure.

Lightweight composites

Carbon fiber CNC service — CFRP machining for robot & structural parts

Answer first: A carbon fiber CNC service (CFRP plate or near-net blanks) is for lightweight robot covers, brackets and structural fittings when molded volume is not ready — not a substitute for every painted ABS shell. CNC vs molded: machine when geometry is still moving, holes/threads must hold, or lot size is prototype–small-batch; mold when the laminate layup and tool are frozen for volume. We do not invent catalogue prices or certificate claims — Upload STEP on /contact/.

FactorCNC carbon fiber / CFRPMolded / formed CFRP
Best forOne-offs, DFM learning, precision holes & edgesFrozen geometry at volume
DFM riskDelamination at exit, frayed edges, dust controlTooling cost / lead before first good part
FixturingSoft jaws / vacuum / sacrificial backing; support thin skinsTool-defined fiber orientation
RFQ must namePlate vs laminate type, thickness, critical edges, qty bandLayup note + cosmetic class
When to switchVolume + stable CAD → mold / RTM pathNeed fast iterations → stay CNC plate

Delamination control

Sharp tools, climb where safe, backing under exit faces, and honest Ra notes — do not ask metal feeds on CFRP.

Fixturing

Support thin skins; avoid crushing honeycomb / foam cores. Call critical edges on the PDF.

What to send

STEP + thickness / fiber note + qty + need-by. Sister: robot shell materials · CNC prototype China.

Upload STEP — carbon fiber CNC RFQ   Materials hub

Metal upgrade path

Aluminum vs titanium — when titanium CNC machining enters the RFQ

Aluminum versus titanium is a cost/weight/strength RFQ choice — not a trivia contest. Stay on aluminum (6061/7075) for most enclosure and fixture prototypes; move to titanium CNC machining when strength-to-weight, corrosion, or biocompatible-adjacent fixtures justify slower cuts and higher stock cost. Machined titanium parts (typically Grade 5 / Ti-6Al-4V) need sharp tooling, flood coolant, and honest lead-time bands — we do not quote catalog pricing here. Sister compares: aluminum vs titanium CNC · aluminum vs stainless China CNC. Factory path: CNC machining China. Upload STEP → /contact/.

Stay aluminum

Covers, brackets, most robot frames — anodize-friendly, fast chips, lower stock cost.

Consider titanium CNC

High specific strength, harsh environment, or weight-critical fittings where stainless is too heavy.

RFQ honesty

Call grade (e.g. Ti-6Al-4V), qty ladder, and finish; expect longer cycle than 6061 — no fake certificates.

Process map

Which China process fits which material

CNC machining

Aluminum first; also ABS, PC, POM plate. Best when fits and threads matter on one-offs and small batches. CNC machining China RFQ.

Vacuum casting / RIM

ABS-like and PC-like resins for 10 to a few thousand covers without steel tools. Vacuum casting China.

3D printing

One-offs and lattices; ABS-like / PC-like resins and metal powder. Post-machine fits if needed. 3D printing China.

Rapid tooling

When geometry is injection-ready and you need real thermoplastic ABS or PC, not a cast stand-in. Rapid tooling China.

Aluminum enclosure route

6061 / 7075 shells beside plastic covers in the same program. Aluminum enclosure China.

Anodize with Al

Finish callouts belong on the aluminum RFQ, not as an afterthought. Anodizing China.

RFQ checklist

What to send when material is still open

You do not need a final grade to start. You do need geometry and the job the part must survive.

ItemPreferredIf missing
3D geometrySTEP / IGES (assembly OK)No route comparison possible
Part jobCosmetic / impact / structure / heatEngineer guesses ABS vs Al
Production intent"Later ABS injection" / "stay Al"Prototype may teach the wrong lessons
Quantity band1 / 10 / 50 / 200+Cast vs CNC vs tool cannot balance
Finish guessPaint / anodize / as-machinedQuoted raw, then re-quoted
Date / IncotermNeed-by; FOB / CIF / DDPLead time stays a range

Upload on /contact (2 files × 4 MB). Broader packing list: RFQ checklist. Tolerance wording: RFQ tolerance guide.

Examples from the base
Decision shortcuts

Fast rules that keep quotes comparable

Painted demo shell → ABS path

Vacuum cast or CNC ABS/PC-ABS; say colour and texture. Do not ask aluminum prices for a paint mock-up.

Load + threads → aluminum

6061 default; 7075 only when the section must stay thin. Put anodize and mask notes on the same RFQ.

Mixed robot program → one crate

Plastic covers + metal frames under one contract. Humanoid robot enclosure China.

ABS vs PC vs aluminumPrototype materials China RFQCNC / cast / 3DP Rapid toolingFOB / CIF / DDP
Related routes

Where to go after the materials decision

Aluminum enclosure China

Metal shell when stiffness, threads or anodize win over ABS/PC covers.

CNC prototype China

First-article metal or plate — bring the part job from this page.

Small-batch CNC China

Repeatable lots; quantity bands 1 / 10 / 50 / 200+ still need the job named.

Humanoid robot enclosure China

Shell RFQ; mix ABS covers with aluminum frames in one crate.

Plastics

ABS / PC-ABS / POM grade behaviour when plastic is the decision.

Carbon fiber CNC / CFRP

Lightweight robot & structural machining vs molded — DFM and RFQ notes on this page.

Contact / STEP upload

2 files × 4 MB — usually within one working day.

Questions buyers ask

Prototype materials FAQ

Which prototype materials for aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China?

ABS for cheap painted covers; PC/PC-ABS for impact and heat; aluminum 6061/7075 for stiffness, threads and anodize. Open aluminum enclosure China or humanoid robot enclosure China for shells; CNC prototype China or small-batch CNC China when cutting metal is the decision. Mixed ABS covers + aluminum frames consolidate in one China crate. Upload STEP on /contact/ (2 files × 4 MB; usually within one working day).

Should my prototype be ABS, PC or aluminum?

ABS for cheap cosmetic covers and painted shells; PC or PC-ABS when impact and heat matter more than ABS; aluminum when stiffness, heat sinking, threads or anodized cosmetics must match the production metal part. Mixed programs often use ABS or urethane covers with aluminum frames in one China crate.

Which China process makes each material?

Aluminum: CNC first. ABS and PC: CNC from plate, vacuum casting in ABS-like or PC-like resins, 3D print for one-offs, or rapid tooling when the geometry is already injection-ready. Everoyal runs those routes at one Suzhou base.

Can vacuum casting replace ABS injection for a small batch?

Often yes for tens to a few hundred cosmetic or light-structural covers. Silicone tools off a machined master give ABS-like or PC-like resins with colour tuning, without steel tooling. When the design is frozen for injection volumes, move to rapid tooling instead. Compare: vacuum casting vs injection moulding.

What should I put on the RFQ if I am still choosing material?

Send STEP geometry, the job the part must do (cosmetic cover, load member, heat sink), quantity band and date. Say if production will later be ABS injection, PC, or 6061. The quote can offer two routes side by side rather than forcing one guess. Upload on /contact/ (2 files × 4 MB).

Do you quote mixed ABS and aluminum assemblies from China?

Yes. Covers, frames and brackets from different process lines consolidate into one crate under FOB, CIF or DDP. Upload the assembly STEP and note which bodies are plastic vs metal.

Which landing for an aluminum enclosure China RFQ after this materials comparison?

Open /services/aluminum-enclosure-china/ when the shell should be metal. Use this page to decide ABS vs PC vs aluminum first, then upload STEP on /contact/.

When should I choose CNC prototype China after reading ABS vs PC vs aluminum?

Open CNC prototype China when first-article metal (or machined plastic plate) is the decision. Bring the job the part must do so the quote is not forced into the wrong material.

How does small-batch CNC China use this materials comparison?

Open small-batch CNC China for repeatable metal lots. Quantity bands such as 1 / 10 / 50 / 200+ still need the part job named so cast vs CNC vs tool can balance.

Can humanoid robot enclosure China programs mix ABS covers with aluminum frames?

Yes. Open humanoid robot enclosure China for shell RFQ language. Use this page for ABS vs PC vs aluminum decision; mixed covers and frames consolidate under one China crate — upload assembly STEP on /contact/.

When should I switch from ABS paint mock-up to aluminum?

Switch when you need stiffness, heat sink, precision fits or anodized cosmetics that match production metal. Do not ask aluminum prices for a paint mock-up; do not ask ABS prices for a load member with threads.

Where do I upload drawings for a materials comparison RFQ?

On /contact/ — up to 2 files, 4 MB each. Note the part job and any production material intent. Rocky Chen replies with route options, DFM risks and a quotation, usually within one working day.

When should I choose aluminum vs titanium for a prototype CNC RFQ?

Default aluminum for speed and anodize; choose titanium CNC machining when strength-to-weight or environment beats stock cost. Aluminum versus titanium should be locked before quoting. Upload STEP → /contact/.

Do you offer titanium CNC machining and machined titanium parts in China?

Yes — machined titanium parts (typically Ti-6Al-4V) on the Suzhou CNC path with honest lead-time bands. Sister factory page → /services/cnc-machining-china/. RFQ → /contact/.

Can ABS/PC prototypes graduate to aluminum or titanium on the same program?

Yes. Start ABS/PC for fit checks, move to aluminum for structural first articles, then titanium only when the RFQ justifies it. Materials hub stays one STEP upload → /contact/.

What is a carbon fiber CNC service and when should I use it vs molded CFRP?

A carbon fiber CNC service machines CFRP plate or near-net blanks for lightweight robot and structural parts while geometry moves or lots stay prototype–small-batch. Mold when layup and tooling are frozen for volume. Call thickness, fiber type, critical edges and qty. See the CFRP table above. Upload STEP → /contact/.

What DFM risks should I watch on carbon fiber / CFRP CNC parts?

Delamination at tool exit, frayed edges, and crushed thin skins from poor fixturing. Use sharp tools, backing on exit faces, and soft/vacuum fixtures. Name critical edges on the drawing. Upload STEP → /contact/.

Also useful: plastics encyclopedia, aluminum encyclopedia, 7075 T6 vs 6061 T6, aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China, contact.

China factory RFQ

ABS, PC or aluminum — Upload STEP on /contact/

Attach STEP, IGES or PDF on /contact/ (up to 2 files, 4 MB each). Note the part job and any production material intent. Rocky Chen replies with route options, DFM risks and a quotation — usually within one working day. Route landings: aluminum enclosure, CNC prototype, small-batch CNC, humanoid robot enclosure.

Upload drawings & get a quote

ContactRocky Chen
BaseSuzhou, Jiangsu, China. Visits by appointment.