Plastic Machining and Parts Manufacturing
Which plastics page vs aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China? Stay here for ABS, PC-ABS, POM, PA, PEEK or PMMA machining and painted covers. Choose aluminum enclosure China or humanoid robot enclosure China when the shell needs metal stiffness, EMI or anodize; open CNC prototype China or small-batch CNC China when cutting metal is the decision — then Upload STEP on /contact/ (usually within one working day).
Updated 2026-11-14 · Semrush cluster P22 · HDPE / nylon · prior P19 Delrin / acrylic · P8 PTFE · P6 Torlon / PEEK · P2b/P3 plastic
Plastics vs aluminum CNC for covers and housings? Engineering plastics here are machined with warping and stress handled in the route. A plastic part that carries a tight flatness callout across a large face will usually cost more than the same part in aluminum because the route has to be split — ribs that hold shape are often cheaper than fighting the material. Route landings: aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China. Compare grades: ABS vs PC vs aluminum. Then Upload STEP on /contact/.
Grades that run here, and what each is for
| Grade | Why choose it | Watch out for |
|---|---|---|
| ABS | Cheap, tough, easy to bond and paint | Soft; fine threads strip, sharp edges burr |
| PC-ABS | Better impact and heat than ABS, still paintable | More notch-sensitive; stress cracking at tight radii |
| POM (acetal) | Low friction, dimensionally stable, machines beautifully | Poor bonding; almost nothing sticks to it |
| PA (nylon) 6 / 66 | Tough, abrasion resistant, good at joints | Hygroscopic: grows with humidity, so allow a settling period |
| PEEK | High temperature, chemical resistance, wear | Expensive and slow to cut; justify it by function |
| Torlon (PAI) | Higher continuous temp / wear than unfilled PEEK in many bearing & seal seats | Harder to machine; name grade (e.g. 4203/4301) and anneal intent |
| PTFE (Teflon) | Lowest friction, chemical inertness, bushings & seals | Soft / cold-flows; hold with soft jaws; not a structural cover grade |
| PMMA (acrylic) | Optical clarity for windows and light pipes | Brittle, crazes under stress and with solvent contact |
| PVC / PP / PE | Chemical resistance, low cost | Soft and gummy; PVC needs corrosion-resistant tooling |
Acrylic is the one most often specified for the wrong reason. It is chosen for a window because it is clear, then found to craze around a fastener two weeks into service. Where a clear window has to take a load or sit near a solvent, polycarbonate is the safer answer even though it scratches sooner.
How plastics machine differently from metal
Three behaviours separate plastic machining from metal machining, and each one changes how a part should be designed rather than just how it is cut.
- Heat, not force, is the limit. Plastic conducts heat poorly, so the chip carries away less of it and the cut edge can soften. Sharp single-flute tooling and a fast feed are gentler than a slow, rubbing pass.
- Internal stress is stored in the sheet. Machining one face of an extruded or cast sheet releases it, and the part bows. Rough, stress-relieve, then finish is the route that holds a flatness callout.
- Clamping marks the surface. Plastic dents under the same pressure that leaves steel untouched, so soft jaws and spread clamping pressure are part of the process, not an afterthought.
The practical consequence for a design: a plastic part that carries a tight flatness or parallelism callout across a large face will cost more than the same part in aluminum, because the route has to be split. Ribs that hold the shape are usually cheaper than a tolerance that fights the material.
Finishing: what sticks and what does not
| Finish | Works on | Note |
|---|---|---|
| Paint, textured or matte | ABS, PC-ABS, PA with primer | Most common route for cosmetic robot covers |
| Vapour polishing | ABS, PC, acrylic | Glossy but attacks fine detail; needs a test part first |
| Tumble / bead blast | Most rigid plastics | Evens out tool marks without changing dimensions much |
| Laser marking | Most, with varying contrast | Contrast depends on the grade; test on the actual batch |
| Electroplating | ABS and plating-grade blends only | Requires a specific resin; not a finish you can add later |
Plating is the one that has to be decided at material selection. An ABS blend that plates well is not the same as a general-purpose ABS, and specifying the wrong one means the plating line rejects the parts after they are already machined.
When plastic parts should be molded instead
Machining a plastic part is the right route from one piece to a few hundred. Past that, the economics move to molding, and the design has to change with them: draft angles, uniform walls and gate positions that a machined part never needed.
If the volume is heading for a tool, design the wall now rather than machining a thick section that will sink when it is molded. The injection molding and tooling page sets out the tool side; the design change is cheaper at R1 than at T0.
Specifying a plastic part on the drawing
Four things on the drawing decide most of the outcome, and three of them are usually missing.
- The grade, not just "plastic". ABS and PC-ABS look identical on a drawing and behave differently under a fastener. Name the grade and, where it matters, the brand.
- Whether it will be painted. A painted face does not need a cosmetic machined finish, and saying so removes a finishing pass from the price.
- Which faces are cosmetic. Tool marks are acceptable on an internal face and not on a visible one, and that distinction is free to state.
- A settling note for nylon. PA absorbs moisture and grows after machining. If a dimension matters, say whether it is measured dry or conditioned.
Wall uniformity is the other one worth a look before quoting. A machined part can carry a 6 mm section next to a 2 mm one without complaint; the same part molded cannot, so if the volume is heading for a tool, evening out the wall now avoids a redesign later.
CNC plastic machining & ABS CNC machining for covers
CNC plastic machining / plastic CNC machining here covers ABS, PC-ABS, POM, PA, PEEK and PMMA — not injection molding. ABS CNC machining is the usual path for painted robot covers and fixtures when metal stiffness is not required. Sister metals: brass & copper. Factory path: CNC machining China. Upload STEP → /contact/.
ABS CNC machining
Fast, paint-ready covers; watch soft threads and sharp edge burrs. Call grade (not just “plastic”) on the drawing.
Plastic CNC parts
From one piece to a few hundred before molding economics win. Flatness across large faces often costs more in plastic than aluminum.
RFQ tips
Name grade, paint/texture, and which faces stay as-machined. Mixed plastic + aluminum BOMs stay one RFQ on /contact/.
Plastic machining, PEEK machining & machined plastic parts
Plastic machining / plastic machining services and plastics for machining here cover engineering grades — not injection molding trivia. PEEK machining / PEEK plastic machining / PEEK machined parts need heat control and sharp tools; call PEEK machinability notes (dry vs coolant, anneal) on the RFQ. Machined plastic parts / custom plastic machining / precision plastic machining run from one piece to a few hundred. Factory path: CNC machining China. Upload STEP → /contact/.
PEEK parts
PEEK gears, bushings, and high-temp housings — name filled vs unfilled grade so cycle time is honest.
Custom machined plastics
Custom machined plastic parts and precision machined plastic parts share the same bay as ABS/POM covers.
CNC machining PEEK services
Say anneal / stress-relief intent up front; PEEK machinability is not the same as ABS CNC machining.
Custom PTFE parts — when Teflon CNC beats PEEK or Delrin
Custom PTFE parts (often called Teflon CNC parts) win when dry-run friction, chemical inertness, or non-stick faces matter more than structural stiffness. Prefer POM / Delrin when dimensional stability and machinability dominate; prefer PEEK (or Torlon PAI in the table below) when continuous temperature and load outrun PTFE. PTFE machines soft — sharp tools, cool cuts, soft jaws, and honest ID/OD callouts. Factory path for metal mates & bushings: custom bushings · CNC China. Upload STEP → /contact/.
| Question | Lean PTFE | Lean PEEK / Delrin (POM) |
|---|---|---|
| Friction / non-stick / chem | Often PTFE | PEEK when load + temp; Delrin when stable sliding + precision |
| Structural stiffness | Weak — not a cover grade | Delrin / PEEK hold shape better |
| Machinability | Soft, cold-flow risk; soft jaws | Delrin excellent; PEEK slower / hotter |
| RFQ must name | Virgin vs filled PTFE, ID/OD, qty | Filled vs unfilled (PEEK) or POM grade |
Custom PTFE / Teflon CNC
Seals, bushings, washers, chemical-facing sleeves — call virgin vs glass/carbon-filled so stock is honest.
vs PEEK / Torlon
Keep the Torlon vs PEEK table above for high-temp wear seats; PTFE is the low-friction fork, not a substitute for PAI.
What to send
STEP + grade note + critical ID/OD + qty. Metal housings share one RFQ on /contact/.
Delrin machining services — acetal CNC and Delrin parts
Answer first: Delrin is the common trade name for acetal / POM. This is the factory CNC path for dimensionally stable, low-friction precision parts, sliding faces and bushings — not a structural enclosure (shells stay on /services/aluminum-enclosure-china/). The grades table above already lists the POM (acetal) row; this block is the RFQ path for Delrin machining services, machining acetal and CNC Delrin. Prefer custom PTFE when lowest friction or chemical inertness wins; prefer Torlon PAI vs PEEK when continuous temperature and wear load outrun Delrin. Materials hub → /materials/ · grade pick → /materials/prototype-materials-comparison/ · prototype path → /services/cnc-prototype-china/. Upload STEP → /contact/.
Acetal machining and machining Delrin plastic need honest workholding: POM conducts heat poorly, clamps can crush faces, and almost no adhesive will bond a Delrin part. Call unfilled vs AF / filled grade, critical sizes and qty on the RFQ. For Delrin machining tolerances, put the numbers on the drawing — this page does not invent a Delrin chart. Tolerance language → /insights/rfq-tolerance-guide/.
| What you searched / called it | What we cut | What to write on the RFQ |
|---|---|---|
| Delrin machining services / machining Delrin / CNC Delrin | Dimensionally stable sliding faces, bushings, precision Delrin parts — not a shell | Unfilled vs AF / filled grade, critical sizes, qty |
| Machining acetal / acetal machining / Delrin plastic machining | Same POM family; Delrin is the common trade name | Same grade, size and qty callouts |
| Delrin machining tolerances | Put the numbers on the drawing — no invented Delrin chart | Critical sizes + drawing tolerances; see the tolerance guide |
Machining Delrin / CNC Delrin
Poor thermal conductivity, clamp crush on faces, and almost no adhesive bond. Plan holding and skip glue-dependent joints.
Machined Delrin parts vs PTFE / PEEK
Delrin parts hold size and slide well. Use custom PTFE for lowest friction or chemicals; use Torlon vs PEEK when heat and wear outrun POM.
What to send
Unfilled vs AF / filled grade, critical sizes, qty and the drawing tolerances. Bushings mates: /services/cnc-machining-china/#custom-bushings.
Acrylic machining — acrylic CNC service for windows and light pipes
Answer first: Acrylic / PMMA / Perspex is the CNC path for optical windows, light pipes and display parts, not a structural cover. The grades-table warning about using acrylic for the wrong reason still stands; this block adds the RFQ and DFM path for acrylic machining services and acrylic CNC machining, including machining Perspex. Grade pick → /materials/prototype-materials-comparison/ · prototype path → /services/cnc-prototype-china/. A metal frame plus a clear window can share one RFQ with /services/aluminum-enclosure-china/. Upload STEP → /contact/.
Call cast vs extruded sheet, whether the face is optical or a general machined face, and whether vapor polish is required. Finish notes belong on /insights/cnc-surface-finish-ra-rfq/ — this page does not invent a transmittance or tolerance table. Watch mounting and fastener crazing. For a load-bearing or solvent-near window, polycarbonate machining is usually safer.
| What you searched / called it | What we cut | What to write on the RFQ |
|---|---|---|
| Acrylic machining / acrylic CNC service / acrylic machining services | Optical windows, light pipes, display parts — not a structural cover | Cast vs extruded sheet, optical vs general face, vapor polish yes/no, mounting |
| Acrylic CNC machining / machining Perspex | Same PMMA family; Perspex is a common trade name | Same sheet, face, polish and mount callouts |
| Polycarbonate machining (contrast, not a new hub) | Usually safer for load-bearing or solvent-near windows | Say PC, not acrylic; metal frame can share the RFQ |
Acrylic CNC machining / Perspex
Name cast vs extruded sheet, optical face vs a general machined face, and vapor polish yes or no. Machining Perspex follows the same PMMA RFQ.
Mounting and polycarbonate machining
Fastener crazing is the usual failure. If the window takes a load or sits near a solvent, specify polycarbonate machining instead of acrylic.
What to send
STEP + sheet process + face / polish notes + mounting. Metal frame and window share one pack on /contact/.
Upload STEP — acrylic machining RFQ Aluminum enclosure China
HDPE CNC machining and custom nylon parts — commodity plastics on a China RFQ
HDPE CNC machining / CNC machining HDPE / machining HDPE is for tanks, wear strips, low-load guides and insulators in a tough polyolefin — not a structural enclosure and not a tight sliding fit. Tight, dimensionally stable sliding parts stay on Delrin / acetal. Custom nylon parts (PA) are the sister when you need more wear or toughness than HDPE; dimensional stability still usually favours Delrin. Upload STEP → /contact/.
HDPE machinability
HDPE cuts easily, but it creeps and moves with temperature. HDPE machinability is not a reason to leave tolerances off the drawing — write the critical dimensions and whether the stock is virgin or regrind. This page does not publish a machinability or tolerance table.
Custom nylon parts
Custom nylon parts in PA can take more wear than HDPE, but nylon also absorbs moisture. If the fit has to stay put, say why you did not choose Delrin. The grade (PA6 vs PA66, any fill) belongs on the RFQ.
What to write on the RFQ
Name HDPE vs nylon vs Delrin, the grade, and any chemical or wear duty. Covers and windows stay on the ABS / acrylic machining notes. Factory path: CNC machining China. Grade pick: prototype materials comparison.
Torlon PAI vs PEEK — when each earns the cut
Torlon PAI (polyamide-imide) and PEEK both sit in the high-temp engineering plastic bay. Choose Torlon when continuous temperature, wear or creep at elevated load outruns unfilled PEEK for bushings, seals or wear pads. Choose PEEK when chemical resistance, toughness at temperature, or a more common supply chain matters more. Neither is a default cover grade — ABS/PC-ABS still win for painted shells. Factory path: CNC machining China. Upload STEP → /contact/.
| Question | Lean Torlon PAI | Lean PEEK |
|---|---|---|
| Continuous service temp / wear seat | Often Torlon (call filled grade) | PEEK when toughness + chem win |
| Machinability / cycle time | Harder; sharper tools, heat control | Still slow vs ABS; easier than PAI for many shops |
| RFQ must name | PAI grade + anneal / moisture notes | Filled vs unfilled + anneal |
| Not for | Cheap painted covers | Cheap painted covers |
Flame / smoke screens (UL 94 V-0, LOI) are application filters — state the requirement on the RFQ; do not assume a cold brand code is stocked. Sisters: PEEK section above · ABS vs PC vs aluminum.
Related routes
Aluminum enclosure China
Metal shell when stiffness, EMI or anodize beats plastic covers.
CNC prototype China
First-article metal cut when plastic is not the material decision.
Small-batch CNC China
Repeatable metal lots; plastic machining here fits one piece to a few hundred.
Humanoid robot enclosure China
Shell RFQ; mix painted plastic covers with metal structure in one RFQ.
ABS vs PC vs aluminum
Side-by-side when the grade choice is still open.
Contact / STEP upload
Rocky Chen — process route, risks and quote, usually within one working day.
Plastics vs aluminum / CNC FAQ
Which plastics page vs aluminum enclosure, CNC prototype, small-batch CNC and humanoid robot enclosure China?
Stay here for ABS, PC-ABS, POM, PA, PEEK or PMMA machining and painted covers. Choose aluminum enclosure China or humanoid robot enclosure China when the shell needs metal stiffness, EMI or anodize; open CNC prototype China or small-batch CNC China when cutting metal is the decision. Then Upload STEP on /contact/ — usually within one working day.
When should I choose plastic instead of aluminum CNC for a cover?
Choose plastic when weight, paintability, impact (PC-ABS) or optical clarity (PMMA/PC) matter more than metal stiffness. Choose aluminum CNC when flatness across a large face, EMI, heat sink or anodize finish drives the design — a plastic part with a tight flatness callout across a large face usually costs more than the same part in aluminum because the route has to be split.
Can you machine plastic to the same tolerance as aluminum?
On a stable grade such as POM or PEEK, yes, in the same range. On soft or hygroscopic grades the achievable tolerance is looser because the part moves after machining, so the design has to allow for it.
Why does my machined plastic part warp after machining?
Stress stored in the sheet is released when one face is cut away. Rough machining, stress relief, then finishing holds flatness; cutting to final size in one pass usually does not.
Do you do plastic laser cutting or only machining?
Machining is the main route for plastic parts here, with cutting and finishing in the same order. For thin sheet work, the process is chosen with the geometry rather than assumed.
Can you supply painted plastic covers in small batches?
Yes. Painting, including textured and matte finishes, runs as part of the same order, so covers arrive finished rather than needing a separate paint shop.
Which landing for an aluminum enclosure China RFQ after this plastics page?
Open /services/aluminum-enclosure-china/ when the shell should be metal. Use this plastics page for ABS/PC-ABS/POM grades and paint routes, then upload STEP on /contact/.
When should I choose CNC prototype China instead of machined plastic?
Open CNC prototype China when first-article metal is the decision. Stay on this plastics page when the prototype is engineering plastic; both routes upload STEP on /contact/ for a usual one-working-day reply.
How does small-batch CNC China relate to plastic small batches?
Open small-batch CNC China for repeatable metal lots. Plastic machining here fits from one piece to a few hundred; past that, economics often move to molding with draft and uniform walls.
Can humanoid robot enclosure China programs mix plastic covers with metal shells?
Yes. Open humanoid robot enclosure China for shell RFQ language. Use this plastics page for painted ABS/PC-ABS covers that sit with metal structure; name both in the same RFQ on /contact/.
When should plastic parts be molded instead of machined?
Machining is the right route from one piece to a few hundred. Past that, economics move to molding and the design needs draft, uniform walls and gate positions. Design wall uniformity now (avoid 6 mm next to 2 mm if a tool is coming) rather than redesigning at T0.
Where do I upload drawings for a plastics or aluminum China RFQ?
On /contact/ — Rocky Chen replies with a process route, tolerance risks and a quotation, usually within one working day. WhatsApp +86 138 2330 4476 and sales@everoyalprecision.com also work.
Do you offer CNC plastic machining and ABS CNC machining?
Yes. CNC plastic machining / plastic CNC machining covers ABS, PC-ABS, POM, PA, PEEK and PMMA. ABS CNC machining is common for painted covers. Upload STEP → /contact/.
When should plastic CNC machining beat aluminum for a cover?
When weight, paintability, impact (PC-ABS) or optical clarity matter more than metal stiffness or EMI. Large flat faces often stay cheaper in aluminum. Compare → /materials/prototype-materials-comparison/. RFQ → /contact/.
Can CNC plastic parts share an RFQ with metal housings?
Yes — name both on one BOM. Metal shells via /services/cnc-machining-china/ or /services/aluminum-enclosure-china/; plastics stay on this page. Upload STEP → /contact/.
Do you offer plastic machining / plastic machining services and plastics for machining?
Yes. Plastic machining / plastic machining services cover ABS, PC-ABS, POM, PA, PEEK and PMMA — plastics for machining named by grade. Upload STEP → /contact/.
Can you machine PEEK / PEEK machined parts / PEEK plastic machining?
Yes. PEEK machining and PEEK machined parts (including PEEK gears when geometry fits) need heat control; call filled vs unfilled and anneal notes. CNC machining PEEK services → same RFQ on /contact/.
What should I send for machined plastic parts / custom plastic machining?
Name grade, paint/texture, and critical faces for machined plastic parts / custom machined plastics / precision plastic machining. Metal shells stay on /services/cnc-machining-china/. Upload STEP → /contact/.
What is Torlon PAI and when should I specify it instead of PEEK?
Torlon PAI is a high-temp polyamide-imide. Prefer it over PEEK when continuous temperature, wear or creep at load dominate. Prefer PEEK when chemical toughness or supply familiarity wins. Name the PAI grade and anneal notes. See the Torlon vs PEEK table above. Upload STEP → /contact/.
Torlon vs PEEK — how do I RFQ the right grade?
State Torlon vs PEEK intent, filled vs unfilled, continuous temp, wear faces, and any UL 94 / LOI screen. Do not treat an obscure brand code as stocked. Upload STEP → /contact/.
Do you stock every UL 94 V-0 / high-LOI plastic brand code?
No. UL 94 V-0 and LOI are application filters — name the flame/smoke need and preferred family (PAI, PEEK, PC, etc.); availability is confirmed with the quote. Upload STEP → /contact/.
Do you machine custom PTFE parts / Teflon CNC parts?
Yes. Custom PTFE parts (Teflon CNC) for seals, bushings and chemical-facing sleeves run with other engineering plastics. Call virgin vs filled, ID/OD and qty. See the PTFE section above. Prefer Delrin for stability or PEEK/Torlon for high-temp load. Upload STEP → /contact/.
When should I choose PTFE vs PEEK or Delrin?
Choose PTFE for lowest friction, non-stick and chemical inertness. Choose Delrin (POM) when dimensional stability and easy machining win. Choose PEEK or Torlon PAI when continuous temperature and wear load outrun PTFE. Bushings mates: custom bushings. Upload STEP → /contact/.
Do you offer Delrin machining services / machining acetal / CNC Delrin?
Yes. Delrin machining services, machining acetal and CNC Delrin are the factory path for dimensionally stable, low-friction precision parts, sliding faces and bushings — not a structural enclosure. Detail → #delrin-acetal. Upload STEP → /contact/.
How should I call Delrin machining tolerances on the RFQ?
Put the tolerances on the drawing — this page does not invent a Delrin chart. Name unfilled vs AF / filled grade, critical sizes and qty. See #delrin-acetal and /insights/rfq-tolerance-guide/. Upload STEP → /contact/.
Do you offer acrylic machining / acrylic CNC service?
Yes. Acrylic machining and acrylic CNC service cover optical windows, light pipes and display parts in PMMA / Perspex, not a structural cover. Detail → #acrylic-machining. Upload STEP → /contact/.
When should I specify polycarbonate machining instead of acrylic?
Specify polycarbonate machining instead of acrylic when the window is load-bearing or sits near a solvent. The existing grades warning still stands; this block adds the RFQ and DFM path. See #acrylic-machining. Upload STEP → /contact/.
Do you offer HDPE CNC machining on a China RFQ?
Yes. HDPE CNC machining / machining HDPE is for tanks, wear strips, low-load guides and insulators — not a structural shell or a tight sliding fit (that stays on Delrin / acetal). Write critical dimensions and stock grade; this page does not publish a tolerance table. See HDPE / nylon. Factory → CNC machining China. Upload STEP → /contact/.
Custom nylon parts or HDPE — which should I specify?
Custom nylon parts (PA) are the usual sister when you need more wear or toughness than HDPE; nylon also absorbs moisture, so a stable fit often still favours Delrin. Name the polymer and grade on the RFQ. See HDPE / nylon. Upload STEP → /contact/.
Plastics or aluminum — Upload STEP on /contact/
Attach drawings on /contact/. Rocky Chen replies with a process route, the tolerance risks in your data and a quotation — usually within one working day. Route landings: aluminum enclosure, CNC prototype, small-batch CNC, humanoid robot enclosure.
Still choosing between plastic and metal? See ABS vs PC vs aluminum, aluminum enclosure China, CNC prototype China, small-batch CNC China, humanoid robot enclosure China — then upload STEP on /contact/.