Aluminum vs Magnesium vs PEEK for Humanoid Robot Parts: A Machining Factory’s Selection Guide
Aluminum carries most humanoid robot structure today because machining, anodizing and cost are mature. Magnesium saves roughly a third of aluminum’s weight but arrives mainly as die castings that still need CNC finishing. PEEK wins gears, bearings and wear parts where heat, friction and weight decide together.
What the published teardowns show
Aibang Robots’ July 2025 material survey collects the published evidence. Aluminum alloy density sits at 2.63 to 2.85 g/cm³, about one third of steel, with tensile strength from 110 to 270 MPa depending on alloy and temper. Magnesium runs near 1.8 g/cm³, roughly two thirds of aluminum. Tesla’s Optimus Gen2 shed 10 kg through magnesium adoption, and Gen3’s knee support lost 42% of its weight. UBTECH’s Walker X hip gearbox, cast in ZM5 magnesium, cut weight 55% versus traditional steel parts and reduced noise by 12 dB. The same survey notes Zhongqing’s SE01 in aerospace aluminum and Unitree’s G1 in aluminum plus plastic, and reprints Goldman Sachs’ 154 billion dollar 2035 market forecast. Read as a set, these teardowns say lightweighting is real, but each gram saved is bought with a specific process, not with a material name alone.
Source: Aibang Robots, upstream core materials survey, 2025-07-25. Goldman Sachs figure is reprinted by Aibang, not a primary source.
Density and process, side by side
| Material | Density (g/cm³) | Dominant process | Where it wins | What it costs you |
|---|---|---|---|---|
| Aluminum 6061 / 7075 | 2.63–2.85 (alloy family) | CNC billet + anodize | Revisable structure, covers, frames | Weight vs magnesium; strength vs steel |
| Magnesium AZ91D / ZM5 | ~1.8 | Die / semi-solid cast + CNC finish | Frozen high-volume housings, gearboxes | Tooling lead time; casting partner needed |
| PEEK | ~1.30 (typical datasheet) | CNC machining, stress-relieved | Gears, bushings, wear and heat parts | Stock price; slower, careful machining |
Aluminum and magnesium values are from the Aibang survey above; PEEK density and the ~250 °C continuous-service figure used below are typical published datasheet values for unfilled PEEK, not a measured lot value.
The machining-factory view: aluminum first
From the machining side, aluminum is the default because the whole chain is mature. 6061 and 7075 bar and plate are stocked everywhere, cut fast, hold tight tolerances without heat drama, and anodize in the same order — Type II for color and corrosion, Type III hard coat for wear surfaces. Everoyal runs both anodizing types in-house, so a machined enclosure leaves one factory with its finish and its inspection report together. Positional tolerance near 0.02 mm and precision bores near 0.01 mm are routine on aluminum with a Zeiss CMM checking the result. When a humanoid program asks for a stiff, light, revisable structure in hundreds of sets, aluminum CNC is the answer that ships this quarter, not next year after tooling. The risk is not capability; it is weight, and weight is where the other two materials enter.
See the aluminum material page for stocked grades and the soft vs hard anodizing comparison for choosing Type II against Type III on wear surfaces.
PEEK: buy it for heat and friction, not for looks
PEEK is a different purchase. At about 1.30 g/cm³ it weighs roughly half of aluminum, shrugs off continuous service near 250 °C, and runs against metal without lubrication in gears and bushings — which is why harmonic-drive and joint wear parts adopt it. Machining PEEK is not machining aluminum: the stock costs far more per kilogram, heat builds in the cut, and burrs and spring-back demand sharp tools, controlled feeds and stress-relief between roughing and finishing. Thin walls can move after machining, so critical bores get a semi-finish pass, a rest, then a finish pass. Everoyal machines PEEK on the same CMM-verified flow as aluminum, but quotes it as its own process, because treating PEEK like cheap aluminum is how parts warp on tight-tolerance joint parts. Plan PEEK parts early, not as a late substitution.
Process notes and tolerances live on the PEEK machining service page.
Magnesium: the saving is cast, then machined
Magnesium’s weight advantage is real — about 1.8 g/cm³ against aluminum’s 2.63 to 2.85 — but the published savings come from casting, not from machining billet. Optimus and Walker X magnesium parts are die cast or semi-solid cast near net shape, then finished. Everoyal does not run a die-casting line, and says so plainly: we take cast magnesium housings and machine the functional surfaces — bearing bores, sealing faces, threaded holes — to the same 0.02 mm positional and 0.01 mm bore standards we hold on aluminum, checked on the Zeiss CMM. If your program needs cast magnesium volume, pair a caster with a CNC finisher. If it needs machined magnesium prototypes, ask us about feasibility first, because chip control and corrosion protection change the process plan and the inspection plan. Both plans belong in the quote, not in a surprise later.
Choose by part function and batch, not density alone
Choose by part function and batch, not by density alone. Structure that must stay revisable — torso shells, shoulder covers, battery housings — goes to aluminum CNC while the design moves. Wear and heat parts — harmonic-drive companions, bushings, gear blanks — go to PEEK even at higher stock cost, because lubrication-free running and 250 °C service remove whole assemblies. High-volume housings with frozen geometry go to magnesium casting plus CNC finishing, where the 55% gearbox weight saving versus steel reported for Walker X can pay for the tooling. The table below maps part types to first choices; the batch column is the tie-breaker, because tooling amortization, not material price, decides most lightweighting budgets in 2026. A material saved per gram can still lose per program if the mold never amortizes within the model’s life. Density is the headline; amortization is the decision.
| Part type | First choice | Why | Batch tie-breaker |
|---|---|---|---|
| Torso shell / shoulder cover | Aluminum CNC | Revisable, anodized, inspected | Any batch while design moves |
| Gear / bushing / wear plate | PEEK | Heat + friction + half weight | Cost per part, not per kg |
| Frozen high-volume housing | Magnesium cast + CNC finish | e.g. Walker X gearbox 55% vs steel | Mold amortizes above ~500 sets |
| Large one-setup frame | Aluminum, five-axis gantry | ~8 × 4.2 × 2.5 m envelope, one datum | Prototype to pilot |
Get a material-and-process quote. Upload STEP, IGES or PDF (two files, 4 MB each) at everoyalprecision.com/contact and tell us the part function and batch size. DFM feedback and a quote usually within one working day; we will say plainly when a material is not our process.
FAQ
Is magnesium always lighter than aluminum for robot parts?
By density yes: magnesium runs near 1.8 g/cm³ versus aluminum’s 2.63 to 2.85, about two thirds the weight for equal volume. But published savings like Optimus Gen2’s 10 kg come from cast magnesium designs, so the saving depends on casting and finishing, not on swapping material in a machined part.
Can PEEK replace aluminum in humanoid robot joints?
In wear and heat parts yes: PEEK at about 1.30 g/cm³ and near 250 °C continuous service runs lubrication-free in gears and bushings. In primary structure usually no, because stiffness per dollar still favors aluminum. Expect PEEK stock and machining to cost more, and plan stress-relief between roughing and finishing.
Does Everoyal die cast magnesium robot housings?
No. Everoyal runs no die-casting line. We machine cast magnesium housings’ functional surfaces — bearing bores, sealing faces, threaded holes — to about 0.02 mm positional and 0.01 mm bore tolerance, verified on a Zeiss CMM, and we machine aluminum and PEEK parts from billet.
Sources
- Aibang Robots, "Humanoid robot lightweighting and intelligence: upstream core materials", 2025-07-25 — aibangbots.com (densities, tensile range, Optimus Gen2 −10 kg, Gen3 knee −42%, Walker X ZM5 −55% vs steel / −12 dB, SE01, G1, Goldman Sachs 2035 $154B reprinted)
Factory figures (tolerances, CMM, anodizing types, no die-casting line) are Everoyal’s own published operating data, checked against the live Everoyal Precision at a glance page on 2026-11-17. PEEK datasheet values are labeled as typical in the body.
Get a material-and-process quote
Upload STEP, IGES or PDF (two files, 4 MB each) and tell us the part function and batch size. DFM feedback and a quote usually within one working day.